Process improvement software

Process improvement software you can use some alternative programs that will be used, such as Griffin, phoenix black box, tornado UFS, JAF, etc. But here I will use the N-BOX tornado as it is popular and easy to use. Before mobile phone repair must meet the requirements, as follows:

1. Battery voltage at least 3.7 Volt (siemens, Samsung, Motorola, and Sony Ericsson => because of type-type voltage is not provided directly by the UFS).
2. Short does not occur on the input voltage. Biloa occur shot must then be corrected before hardware, namely: resistansi check on the phone interface battery engine, 6 Ohm resistansinya maximum, then you flip polaritaskabel avometernya, the phone should show no movement occurs in the needle instructions.
3. Flash interface on the PCB must be clean. If dirty then you must first clear the brush and given a little thiner ago dried.
4. Once the phone is connected to the UFS tornado, after clicked "check" the phone must terdetek, diLCD although there are not any posts tesmode or local mode (especially Nokia). How to detect something like this:

• Use the program Ð DCTx tools
• connect the phone to UFS tornado
• Choose a type mobile phone according to the type of phone will be detected.
• Click on "check", DCTx tools will be the "1st Boot OK, WD2/DCT4, UPP: 0 ... ... ....." Error when the phone can not be detected by DCTx tools, then the damage is still on the hardware.

When tidah meet the requirements above then the damage is still possible in the hardware.

TROUBLE SHOOTING

Audio Pbroblem:

1. Speaker Problem
2. MIC Problem
3. Buzzer OFF


Charging Problem:

1. Display Appears Not Charging
2. Charging Display Appears But Not Moving
3. Charging Display and comes Moving But Not the


LCD Problem
UI Problem:

1. Vibra OFF
2. Light OFF


Insert SIM
Hank Key pad
Signal Problem
Total dead
AUDIO PROBLEM

1. Speaker Problem
Step work:

* Check component mekaniknya
* Check speaker + resistor - 300 ohm
* Impedance check with the speaker pad ground
* Impedance speaker check pad (+) and C179 with the speaker pad (-) with the C180, if OK replace the zero-L150, R151, C179, C180.
Impedance * If there is all the damage is on the audio prosesornya, which terletek in IC UEM.

2. MIC Problem
Step work:

* Check mechanical component connectors
* Check resistansi MIC + - 1 Kohm
* Impedance MIC check with the ground pad
Impedance MIC check * pad (+) with the C171, if OK replace the zero-L153, R153, C159, C153, C171, C172
* MIC bias in check R160, zero if OK replace the R156, C183, C175, R160, C152
Impedance * if there is all the damage in the IC UEM

3. Buzzer OFF
Step work:

* Check mechanical components konektornya
* Check resistansi Buzzeer
* Impedance check with buzzer pad ground
* Impedance check on the pad with a buzzer C164, C165 buzzer pad down, zero if OK replace the L151, L152, C177, C178, C164, C165
* If the treatment above is correct then there is damage to the IC Audio Amplifier (N150)


Charging PROBLEM

1. Display Appears Not charging
Step work:

* Check resistansi F100 and L100 zero if the components change
* Impedance check Vcharge with the ground path, zero if OK replace the V100

2. Charging Display Appears But Not Moving
Step work:

* Check out voltage of the battery connector + - 3.8 volt

3. Charging Display and comes Moving But Not the
Step work:

* Impedance check instead of R250 if necessary, zero if OK replace UEM IC

LCD PROBLEM
Step work:

* Solder re-foot-foot connector B to B LCD
* Check voltage V10 dah Vflash, zero if OK replace the C300, C301

UI PROBLEM
Vibra OFF
Step work:

* Check resistansi Vibrator, if not replace the rotary
* Check Vbaterai + - 4 volt
* Vibra Impedance check with the ground pad

Light OFF
Step work:

* Check N300, L300, V300

INSERT SIM
Step work:

* Clean the connectors simcard
* Foot-soldier back foot simcard
* Reprint R388

Hank keypad
Step work:

* Reprint Z300 Keypad IC, if still no damage to hank on the CPU / UPP

Signal PROBLEM
Step work:

* Manual Search: Phone settings à Network à Network mode: manual (take this)
* Automatic

OFF TOTAL
Step work:

* Check voltage swith on / off 1 - 1.5 volt check voltage out from the IC Power check box with a flasher, select the normal mode is zero if OK, press the check

(ISI Boot OK, UPP, 3450, ... ... F10, 0x 0000 0000, 0x0130 PPFF, ... ...)

* Do the flashing

Logic HANDPHONE

Harware (hardware):

RF BB à à UI
RF: Radio Frequency
BB: BaseBand à Power IC, CPU, Flash IC, etc.
UI: User Interface à Vibra, Led, buzzer

Software (software / FRIMWARE):

À MCU system
PPM à languages
EePROM à IMEI
HARDWARE (THE HARD)

1. RF (Radio Frequency)
RF system is the part that serves to transmit information, this section will act as a wireless system in the cellular system. RF System there are two sets of RF terintergrasi in the system, namely:

* SA: Swith Antenna
* LNA: Low Nois Amplifier
* RF: Radio Frequency
* VCO: Voltage Control Oscilator
* PA: Power Amplifier
* OSC: Oscilator
* RX: Receiving data dibase information station
* TX: The sender of data information to base station

2. BB (BaseBand)
This section is part of the input or output of the entire phone system.
3. UI (User Interface)
UI (User Interface) is the section that will connect information from the phone system to mobile phone users, or vice versa, eg you will send SMS, then you should be pressing the phone keypad so you can receive commands that we type. Or there is an incoming call to the mobile phone the phone will ring so that users can immediately receive a phone call. Components that are always associated with one mobile phone users such as keypad, LCD, buzzer, Vibrator, LED, etc..

SOFTWARE (SOFTWARE)

1. MCU
MCU (Micro Controller Unit) is the operating system program data, which contains routine-routine, procedures, version, logic, blutooth code, but also to control and coordinate the activities of a oprasai system.
2. PPM
PPM (Post Memory Programming), namely the data from the program containing the software language, ringtone, picture, fantasy, a list of all network, country code, etc.. Language is a software program created as a translator between the written language with the day-to-harimenjadi bahassa engine berbentukbilangan binary. Bundles / language options available on the phone, called language pack. Software language on nokia mobile phone are on the PPM data. Language packs that are on the phone will vary depending on the area for phone sales, eg if the phone will be sold to Europe by the manufacturer on the akan language packnya not there is a choice of languages of Indonesia. Unlike the mobile phone that will be sold diasia, in the language selection will be English.
3. EEPROM
EEPROM (Electrically Erasable Programmable Read Only Memory) has a duty to save the information that has been programmed by the manufacturer the phone itself. stored in the EEPROM are:

* No IMEI (International Mobile Equipment Identifier)
* Security code
* ESN (Electronic Serial Number)
* MIN (Mobile Identification Code)
* SID (system Identification Code)

PHONE NOKIA BB5

Nokia mobile phone that has a dual processor is the BB5. The phone has a sophistication that is not owned by the previous Nokia (DCT3, DCTL, DCT4, WD2). Nokia BB5 mobile phones such as Nokia 6630, 6680, 6681, N series.

BASIC CONCEPT TECHNOLOGY Cellular

Mobile System is a sophisticated system because this system divide the area in a few small cells. This is used to ensure that the frequency can be extended so that it reaches to all parts of the region in particular so that multiple users can use their mobile phones simultaneously without pause and without falter.
DEFINITION Cellular

In the cellular system, to describe the geographic coverage area digunakanlah representation heksagonal. This is the area that disubut cell (cell). Why not the circle shape heksagonal to describe a cell?
If you describe a cell in the form of a circle, then the cells with each other will not be continuous with each other perfectly. In the cellular system, all areas can dicakupi without gaps cells with each other so that more kurva heksagonal represent, because the coverage area can tergambarkan with rapih and covers the entire area.
Where an antenna will be able to send and receive signals on the three different regions, where each cell is only partially covered only three of the cells covered.
Bebrapa forming an important component of the cellular system is the mobile equipment itself, such as Base Station Radio, Antenna and Base Station Controller will manage lalulintas of some cells that are interconnected with the public telephone network.